Quick Installation Sheet
CM-170
model no.
Please carefully read these instructions before using this product.
Save this manual for future use.
28550AA
170 Series Outdoor Dome
RoHS
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against armful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modifications not expressly approved by seller.
The party responsible for FCC compliance could void the user’s authority to operate the equipment and could create a
hazardous condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR 11
CISPR 22
ANSI C63.4
CE: EN50130-4
Emissions
Immunity
CM-170
Type / Format
Scanning Element
Image Picture Element
Effective Picture Element
Resolution (TV Lines)
Minimum Illumination
S/N Ratio
Back Light Compensation
Exposure Control
Sync System
Gamma Compensation
Video Output
White Balance
Auto White Balance Range
Power Range*
Power Consumption
Operating Temperature
Storage Temperature
NTSC
2:1 Interlace,
H15.734KHz/V :59.9Hz
1/3” Interline CCD
768 (H) X 494 (V)
480
1.2 Lux @ F1.6
48dB
Central Area for DC IRIS Lens
DV Type Auto IRIS Control
INT
0.45
1.0Vpp, 75 Ω Unbalanced
Automatic White Balance
2500°K --9700°K
DC 12V
±10%
2.2W (Max)
-10°C ~ +50°C
-20°C ~ +60°C
Model No.
Regulatory Compliance
General Specifications
Hardware Kit Contents
Lens Specifications
A1 : Focus Adjuster
A2 : Field of View Adjuster
A1
A2
A3
TILT 90°
ROTATE 360°
PAN 360°
Angle Adjustment
Do Not Overturn
B1 : Function Control Dip Switches B2 : AI Level Adjustment*
*AI Level Adjustment is factory set and hould not normally require adjustment.
Switch 2
ONOFF
Back Light Compensation
Auto Gain Control
OFF
(Normal Mode)
ON
(Turbo Mode)
Switch 1
Camera Adjustments
Function Control Dip Switches
• 1/2” Rubber Grommet
• 3/4” Rubber Grommet
• Screw Pack
• Torx Driver
• Wire-Ended Power Adaptor Lead
• Quick Install Adaptor
Focal Length
F-No.
Iris Range
Minimum Object Distance
Field of View
BLC
AGC-UP
Low Light Croma Suppression
4mm~9mm
F1.6
F1.6~F2.4
50cm (19.7”)
92.8°~39.4°
71.0°~31.6°
51.6°~23.6°
ON/OFF
ON/OFF
AUTO
Diagonal
Horizontal
Vertical
T1
T2
Template
Cable Access Using Base Cable Entry
Surface Mount (wall or ceiling)
Using Quick Install Adaptor:
Using Locking Arms:
Using Screws:
Cable Access
T1
T1
T1
T5
T5
T3
US Single Gang Box
US Single Gang Box
T4
3/4” NPT
Cut a 1.5” (38mm) hole in the mounting surface as
indicated by T2. The hole can also be used for
cable access.
Cut a 4.3” (110mm) hole in the mounting surface as
indicated by T3. The hole can also be used for
cable access.
Drill four holes at template positions T1 and use the
screws and anchors provided in the screw kit if they
are appropriate for the mounting surface.
When mounting the camera on a surface with the
provided screws, use one of the side knock-outs, as
indicated on the template, for cable entry.
To thread the cables through the mounting
surface, cut a 3/4” (19mm) hole as
indicated by T4.
Note: When mounting on a US Single Gang Box,
use the pre-drilled holes in the dome base as
indicated by T5.
(50 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern